Sauder 414729 Manual de Instruções

NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-24Français pg 25-28Españo

Step 6 åFasten the MOLDINGS (M and N) to the TOP (E). Tighten two TWIST-LOCK® FASTENERS.414729 www.sauder.com/servicesPage 10EMNHow to use the SAUDER

åFasten two CORNER BRACKETS (31G) to the MOLDINGS (M and N) and TOP (E). Use eight BLACK 9/16" LARGE HEAD SCREWS (1S). åFasten two METAL BRACKET

Step 8 åFasten the LEFT END (B) to the LEFT MOLDING (N). Tighten two HIDDEN CAMS. åFasten the SMALL UPRIGHT (D) to the TOP (E). Tighten the TWIST-LOCK

åFasten the SHELF (G) to the LEFT END (B). Tighten two HIDDEN CAMS. åFasten the SHELF (G) to the SMALL UPRIGHT (D). Use two BLACK 1-7/8" FLAT HE

Step 10 åFasten the UPRIGHT (C) to the SHELF (G). Tighten two HIDDEN CAMS. åFasten the SHELF MOLDING (S) to the SHELF (G). Use four BLACK 9/16" L

åFasten the BOTTOM (F) to the LEFT BASE (Q). Tighten two HIDDEN CAMS. åFasten the BOTTOM (F) to the UPRIGHT (C). Use two BLACK 1-7/8" FLAT HEAD

Step 12 åFasten the RIGHT END (A) to the RIGHT MOLDING (M), SHELF (G), and BOTTOM (F). Tighten six HIDDEN CAMS. åPush the MAGNETIC CATCH (2I) into the

åFasten an END MOLDING (T) to the RIGHT END (A). Tighten two HIDDEN CAMS. åFasten the other END MOLDING (T) to the LEFT END (B). Use two BLACK 9/16&q

Step 14 åCarefully turn your unit over onto its front edges. åInsert two LONG METAL PINS (3R) into the holes in the CROSS SHELF (H). Push two SMALL CR

åUnfold the BACK (J) and lay it over your unit. åFasten the BACK (J) to your unit using the NAILS (1N). åNOTE: Be sure to tap NAILS into the holes th

Table of Contents Assembly Tools Required345-2425-2829-3233-3435Part Identifi cationHardware Identifi cationAssembly StepsFrançaisEspañolSafetyWarrantyH

Step 16 åFasten the HINGES (27H) to the DOOR (K). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). åFasten the STRIKE PLATE (6I) to the DOOR (K). Use

åCarefully stand your unit upright. åFasten the DOOR (K) to the RIGHT END MOLDING (T). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). åFasten the

Step 18 åPush the RUBBER SLEEVES (2R) over the METAL PINS (1R). Insert the METAL PINS into the hole locations of your choice in the END (A) and UPRIGH

åWe recommend using the SAFETY BRACKET (1G) for added stability. Use a BLACK 9/16" LARGE HEAD SCREW (1S) into the top of the unit and a BLACK 1-

Step 20 åTo help prevent the TV from sliding, place the ANTI-SKID PAD (3M) under the front support of the TV or divide among the front supports if mor

A l’usage exclusif du Canada Noter la date d’achat de cet élément et conserver le livret pour future référence. Pour contacter Sauder en ce qui concer

AVERTISSEMENTL'utilisation d'un téléviseur trop lourd ou trop gros est dangereuse. Un téléviseur trop lourd créera un risque de basculement

ÉTAPE 7Fixer deux SUPPORTS EN CORNIÈRE (31G) aux MOULURES (M et N) et au DESSUS (E). Utiliser huit VIS TÊTE LARGE 14 mm NOIRES (1S).Fixer deux CONSOLE

ÉTAPE 15Attention: Ne pas relever l'élément dans sa position verticale avant d'avoir fi xé l’ARRIÈRE. L'élément risque de s'e ondr

A l’usage exclusif du Canada Noter la date d’achat de cet élément et conserver le livret pour future référence. Pour contacter Sauder en ce qui concer

Part Identifi cation å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar

ADVERTENCIAEl uso de un televisor demasiado pesado o grande es peligroso. Un televisor demasiado pesado generará riesgo de caída, lo cual podría causa

PASO 7Fije dos MÉNSULAS DE ESQUINA (31G) a las MOLDURAS (M y N) y al PANEL SUPERIOR (E). Utilice ocho TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (1S).

PASO 15Precaución: No coloque la unidad en posición vertical hasta que se fi je el DORSO. La unidad podría caerse.Desdoble el DORSO (J) y colóquelo sob

414729www.sauder.com/servicesPage 33AVERTISSEMENTPrière d’utiliser le mobilier à bon escient et avec prudence. Une mauvaise utilisation peut être à l’

414729 www.sauder.com/servicesPage 34ADVERTENCIAPor favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridado daño

1. Sauder Woodworking Co. (Sauder®) provee cobertura de garantía limitada al comprador original de este producto por un período de cinco años, a parti

Register your new product onlineFor immediate service, our website is available 24 hours per day, seven days per week, to order replacement parts, acc

Hardware Identifi cation å Screws are shown actual size. You may receive extra hardware with your unit.414729 www.sauder.com/servicesPage 4WARNINGNever

Step 1Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips åAssemble your unit on a carpeted fl oor or on the

Step 2 åPush twenty HIDDEN CAMS (1F) into the ENDS (A and B), UPRIGHT (C), BOTTOM (F), and SHELF (G). Then, insert the metal end of a CAM DOWEL (2F) i

åFasten ten ANGLE BRACKETS (27G) to the ENDS (A and B) and SHELF (G). Use ten BLACK 9/16" LARGE HEAD SCREWS (1S). åNOTE: Be sure the edges of th

Step 4 åTurn eight CAM SCREWS (8F) into the MOLDINGS (M and N) and BASES (P and Q).414729 www.sauder.com/servicesPage 88FQPMN(8 used)

åFasten the RIGHT BASE (P) to the RIGHT END (A). Tighten two HIDDEN CAMS. åFasten the LEFT BASE (Q) to the LEFT END (B). Tighten two HIDDEN CAMS.Step